19 November 2026 · Copper procurement · 12 min read · The MetalAlert team

How to calculate your copper exposure from the bill of materials and annual volumes

Most manufacturers know what they spend on copper wire or busbar. Far fewer know how many tonnes of copper they are actually exposed to, because much of it is hidden inside brass fittings, cables and bought-in motors, and because some of it is priced on an LME index while the rest sits in fixed-price contracts that will reprice later. Without that number, a hedge ratio, a copper budget or a margin sensitivity is guesswork.

Cutaway of an electric motor showing copper windings inside the housing
Image: pqinstitute / Pixabay

The calculation itself is straightforward: copper exposure = annual units x copper content per unit (gross of yield loss), minus scrap credits, split by how and when each part is priced, then multiplied by the copper price. The useful outputs are tonnes, value in USD and in your budget currency, and the cost impact of a US$1,000/t move. In the worked example below, a mid-sized manufacturer with three product lines ends up with about 84 t of net copper exposure a year, which means every US$1,000/t change in the LME price is worth roughly US$84,000 (about EUR 75,000) a year.

This exposure figure is the foundation for everything MetalAlert is designed to support. A probability that copper rises by a given amount over the next three months only becomes a decision once you know how many tonnes that move applies to and when they are priced.

Why spend data is not enough

Purchasing spend by commodity code tells you what you paid for "cables" or "motors". It does not tell you how much of that price was copper, whether the copper element moved with the LME, or when it will reprice. Two common blind spots:

A bill of materials (BOM) approach captures both, because it starts from the physical copper in what you make.

Step 1: Explode the BOM down to copper-bearing items

Start from the products you sell and expand each BOM to its purchased parts. Flag every line that contains copper or a copper alloy:

You do not need every screw. In most products, a handful of lines account for the large majority of copper. Start with those and add detail where the numbers justify it.

Step 2: Convert each item to kilograms of copper

Each item type needs a different conversion.

Pure copper semis: geometry and density

For busbar, strip or tube, copper weight is volume x density. Annealed copper conductors weigh about 8.9 kg per kilometre for each square millimetre of cross-section, which is the same as a density of about 8.9 g/cm³. As a cross-check, Nexans lists a bare 25 mm² copper conductor at approximately 223 kg/km, or 8.92 kg/km per mm² (Nexans).

Example: a 30 x 5 mm busbar, 600 mm long, is 90 cm³ of copper, so about 0.80 kg.

Cables: kg per km

For cable, multiply the copper conductor cross-section by 8.9 kg/km per mm² and by the number of cores. A four-core 16 mm² cable carries about 4 x 16 x 8.9 = 570 kg of copper per km. Datasheets often state copper weight directly (sometimes called "copper number" in kg/km), and that figure is better than a calculation because it reflects the actual stranding. Use it where you have it. Remember to exclude armour, screens or aluminium conductors if they are not copper.

Brass and bronze: copper share of the alloy

Alloys are converted using the copper share of the grade. Under EN 12167, CuZn37 (CW508L) contains 62-64% copper and the free-machining brass CuZn39Pb3 (CW614N) 57-59%, with tin bronzes such as CuSn8 being mostly copper with 7.5-8.5% tin (EN 12167 composition table). A 0.25 kg CuZn39Pb3 fitting therefore contains about 0.145 kg of copper at a 58% midpoint.

One caveat: brass parts are often priced off a brass or alloy base, not directly off LME copper, and zinc prices also play a part. Treat the copper share as exposure to copper, and note that the pass-through may not be one-for-one.

Bought-in components: ask the supplier

For motors, transformers and similar parts, ask the supplier for the copper weight per unit. Suppliers that apply copper surcharges already know it, because the surcharge is calculated from it. If they will not disclose it, estimate from teardown data or a comparable product and flag the line as an estimate. For checking a supplier's surcharge arithmetic once you have the weight, see how a copper surcharge is calculated.

Step 3: Add yield loss and subtract scrap credits

What you buy is more than what ends up in the product. Busbar is cut from longer bars, cable is cut to length, and stamping leaves skeleton scrap. Your exposure is on the gross copper you buy.

Some of that loss comes back as clean scrap, which you sell at a price linked to copper, typically at a discount to LME. That sale offsets part of the exposure. The offset is:

scrap credit (t of copper equivalent) = scrap tonnes x scrap recovery (% of LME value)

Two cautions. Scrap credits arrive later than the purchase, so the timing does not match. And low-grade mixed scrap (such as insulated cable offcuts) may recover so little that it is not worth modelling.

Step 4: Multiply by annual volumes

Use the sales and operations plan or the budget volumes for each SKU, including spare parts and service kits, which are easy to forget. For a 12-month view, use monthly volumes rather than an annual total, because Step 6 needs the timing.

Step 5: Classify each line by pricing basis

This is the step most exposure calculations skip, and it determines when the exposure hits you.

Pricing basis Example When copper price changes hit your cost
Index-linked, short lag Busbar at LME monthly average plus fabrication; cable with a monthly copper surcharge Next pricing period, often the following month
Fixed for a period Brass parts at a quarterly fixed price At the next repricing date
Fixed until contract renewal Motors on an annual fixed-price contract All at once, when the contract renews
Customer pass-through Your own sales contracts with copper clauses Offsets exposure, with its own lag

The last row matters. If some of your selling prices carry copper adjustment clauses, part of your purchase exposure is offset by sales. Net it off only to the extent that the clause really moves with your costs. The mechanics are covered in back-to-back copper pricing.

Step 6: Build the timing profile

Spread each line over the months in which it is priced, not the months it is delivered. A cable delivered in January but priced on the December average is December exposure. A fixed annual contract that renews on 1 April creates a single pricing event for the whole contract year.

This profile is what a hedge programme or a purchase-timing decision works from. It also shows whether a large share of your annual exposure is priced on just a few days, which concentrates risk.

Step 7: Convert to money and sensitivity

Multiply net tonnes by a reference copper price to get value, and convert to your budget currency. Then calculate the sensitivity, which is simpler and more useful than the value:

Remember that copper is priced in US dollars. For a EUR or SEK budget, the exchange rate is a second exposure (see how to hedge copper bought in USD with a EUR or SEK budget).

Worked example: a manufacturer with three product lines

All figures below are illustrative. The company, BOM, volumes and prices are invented to show the method. Copper price US$14,400/t and EUR/USD 1.12 are round assumptions close to late October 2026 levels (Business Recorder/Reuters).

SKU A: copper explosion for one drive cabinet

Component Qty per unit How copper is calculated Net Cu (kg) Gross Cu bought (kg) Pricing basis
Busbar Cu-ETP 30 x 5 mm 0.6 m 90 cm³ x 8.9 g/cm³ 0.80 0.92 (cut from bar; 0.12 kg offcut) LME monthly average + fabrication
Power cable 4 x 16 mm² 3 m 4 x 16 x 8.9 kg/km x 0.003 km 1.71 1.76 (3% cutting waste) Monthly copper surcharge
Control wire 1.5 mm² 25 m 1.5 x 8.9 kg/km x 0.025 km 0.33 0.35 (5% waste) Monthly copper surcharge
Brass fittings CuZn39Pb3 0.25 kg 58% copper 0.145 0.145 Fixed price per quarter
Motor (bought in) 1 pc Supplier-declared winding weight 2.00 2.00 Fixed annual contract, renews 1 April
Total 4.99 5.18

All SKUs: annual exposure by pricing basis

SKU Units/year Gross Cu (kg/unit) Index-linked (t) Fixed quarterly (t) Fixed annual (t) Gross total (t) Clean scrap (t)
A: drive cabinet 8,000 5.18 24.25 1.16 16.00 41.41 0.95
B: compact cabinet 15,000 2.40 19.50 1.50 15.00 36.00 0.90
C: busbar spare kits 6,000 1.50 9.00 0.00 0.00 9.00 0.90
Total 52.75 2.66 31.00 86.41 2.75

Assuming clean busbar scrap is sold at 92% of the LME value, the scrap credit is 2.75 x 0.92 = 2.53 t of copper equivalent. Net exposure is 86.41 - 2.53 = 83.9 t a year.

Timing: when the exposure is priced

Assume volumes are spread 24% / 27% / 22% / 27% over the four quarters (Q3 is lighter because of summer shutdown).

Quarter Index-linked (t) Brass, priced at quarter start (t) Motor contract (t) Scrap credit (t)
Q1 12.7 0.64 7.4 (already priced under the contract signed last April) -0.61
Q2 14.2 0.72 8.4 -0.68
Q3 11.6 0.59 6.8 -0.56
Q4 14.2 0.72 8.4 -0.68

Two findings stand out. First, 23.6 t (the motor volume for April to December, about 28% of annual net exposure) is repriced on a single day, 1 April. That one renewal deserves its own plan, whether that is negotiating the copper element on an index or hedging ahead of it. Second, 7.4 t of next year's exposure is already fixed, so the open exposure for the coming budget year is about 76.5 t, not 83.9 t.

Value and sensitivity

Measure Tonnes USD EUR (at 1.12)
Net annual exposure at US$14,400/t 83.9 1,207,800 1,078,400
Impact of a US$1,000/t move 83,900 74,900
Impact of a US$100/t move 8,390 7,490
Open exposure for the budget year, per US$1,000/t 76.5 76,500 68,300

That last line is the number to bring into a budget discussion. How these tonnes translate into budget scenarios is covered in building a copper budget with best, base and worst-case scenarios, and the effect on profitability in how a US$1,000/t copper move hits gross margin.

Spreadsheet structure you can copy

One row per SKU-component combination. Suggested columns:

Column Content
SKU, component part number, supplier Identification
Material / alloy grade e.g. Cu-ETP, CuZn39Pb3, cable type
Unit of measure and quantity per SKU m, kg, pcs
Copper conversion factor kg Cu per unit of measure (density, kg/km, alloy %)
Source of factor Datasheet, standard, supplier declaration, estimate
Net Cu kg per SKU Quantity x factor
Yield loss % and gross Cu kg per SKU Net / (1 - loss) or net + measured offcut
Scrap type and recovery % of LME Clean, mixed, none
Monthly volumes (12 columns) From S&OP or budget
Pricing basis Index-linked, fixed period, fixed contract, pass-through
Price reference and lag LME cash average M-1, DEL base, fixed
Repricing date For fixed contracts
Monthly priced tonnes (12 columns) Volumes shifted by lag or bunched at repricing
Price and FX assumptions USD/t, EUR/USD
Exposure USD and EUR, sensitivity per US$1,000/t Calculated

Keep the conversion factors on a separate tab so they can be updated once and flow everywhere.

Common mistakes

FAQ

How accurate does a copper exposure calculation need to be?

Accurate enough to support the decision. As a rule of thumb, for setting a hedge ratio or a budget range, being within 5-10% on total tonnes is enough. Spend effort on the largest lines and the timing of repricing events rather than on small parts.

How do I find the copper content of a cable?

Use the copper weight in kg/km from the datasheet if it is listed. Otherwise multiply the copper conductor cross-section in mm² by about 8.9 kg/km and by the number of copper cores.

Should scrap credits reduce my hedge volume?

Only for clean scrap with a reliable, copper-linked sale price. Because scrap is sold later than copper is bought, many companies hedge the gross purchase and treat the scrap credit as a separate, smaller offsetting exposure.

Sources

From tonnes to decisions

Once you know how many tonnes are open and when they are priced, the next question is how likely it is that copper moves enough to matter before each pricing date. If you want to see how probability estimates for LME copper over defined horizons could be applied to your own exposure profile, MetalAlert is built for exactly that question. A probability does not decide for you, but combined with a clear exposure figure it shows where the risk in your purchasing calendar is concentrated.

Book a walkthrough Get early access
← All posts MetalAlert home